Simple Setup of SanMats Shoe Sanitising System

WHY SANMATS? SHOP NOW

SanMats System Setup Process

NOTE: It is recommended to place SanMats System as shown in the picture.

  1. Place the Base on a flat surface near the entrance of your home, office, shop, business premises etc.

  2. Place the insert on the base.

  3. Gently pour 2 litres of disinfectant solution over the insert.

  4. Place the dryer on the exit side of the base.

  5. Now the SanMats System is ready to function to disinfect your shoes from germs (99.99%).


SanMats 2-In-1 Setup Process

NOTE: It is recommended to place SanMats 2-In-1 as shown in the picture.

  1. Place the Rubber Base on a flat surface near the entrance of your home, office, shop, business premises etc.

  2. The base has 2 compartments, place the insert and the dryer on each of it.

  3. Gently pour 1 litres of disinfectant solution over the insert.

  4. Now the SanMats 2-In-1 is ready to function to disinfect your shoes from germs (99.99%).

Disinfection Process

  1. Place your feet over the mat for 2-3 seconds.

  2. The disinfectant solution on the mat will wet the shoe sole to disinfect it.

  3. Dry your shoe sole on the anti-skid dryer to avoid slipping on the floor.

Disinfectant Solution

We recommend following disinfectants (easily available on retail outlets & online stores) to be used in the SanMats System, you may also use any other disinfectant liquids (without Sodium Hypochlorite Content) available in the market & prepare the disinfectant solution as directed on it.

  1. Lizol Disinfectant Surface Cleaner

  2. Add 1/2 cap (6 ml) of Lizol Disinfectant Surface Cleaner in 2 litres of clean water to prepare the disinfectant solution for the SanMats System.

    Add 1/4 cap (3 ml) of Lizol Disinfectant Surface Cleaner in 1 litres of clean water to prepare the disinfectant solution for SanMats 2-in-1.

  3. Dettol Disinfectant Liquid

  4. Add 2 caps (30 ml) of Dettol Disinfectant Liquid in 2 litres of clean water to prepare the disinfectant solution for the SanMats System.

    Add 1 caps (15 ml) of Dettol Disinfectant Liquid in 1 litres of clean water to prepare the disinfectant solution for the SanMats 2-In-1.

  5. Presto Disinfectant Surface Cleaner (Amazon Brand)

  6. Add 1/2 cap (7.5 ml) of Presto Disinfectant Surface Cleaner in 2 litres of clean water to prepare the disinfectant solution for the SanMats System.

    Add 1/4 cap (3.75 ml) of Presto Disinfectant Surface Cleaner in 1 litres of clean water to prepare the disinfectant solution for the SanMats 2-In-1.

Refilling the SanMats System

The SanMats System can be refilled with disinfectant solution by gently pouring it over the insert whenever it becomes dry with use, avoid over refilling otherwise the disinfectant solution will overflow from the base.

NOTE: To prepare one litre refill of disinfectant solution, mix the correct ratio of the disinfectants with clean water as instructed above.

Cleaning the SanMats System

  1. Cleaning the SanMats System is very easy, it is recommended to clean it Weekly. Remove the insert from the base, remove the left over disinfectant solution from the base, clean the insert & the base with plain water, dry it for 10 – 15 minutes.

  2. Clean the dryer by removing dust from it by using a broom or vacuum cleaner. SanMats System is again ready for use by adding disinfectant solution on it.

  3. Liquid or powder detergents can be used to clean the base, insert or dryer ( once in a week or whenever it becomes dirty).

Important Instructions:

  1. Read safety instructions of the disinfectants before use.

  2. Do not use Sodium Hypochlorite (Bleach) solution or any Alcohol based sanitisers in SanMats Systems

  3. If SanMats System is used barefooted than kindly wash your feet after the sanitisation process.

SanMats System setup process video